5 Litre Jerry Can Mould
Two-cavity blow mould for a five litre stackable jerry can, with Beryllium Copper at the neck and the base pinch-off.
- Cavities
- 2
- Capacity
- 5 litre
- Material
- Tooling steel
Who this tooling is built for.
The sectors we supply, the containers each one runs, and the moulds we have built for them.
Sector
Lubricant Packaging
The largest part of the work. Oil and lubricant packers have been the core customer since the beginning, and most of the tooling on this site was built for them.
Lubricant packs are unforgiving in a specific way: the container has to stack, the handle has to take the weight of a full five litres, and the closure has to seal against an oil rather than water. We build the container and its cap together so the pair is trialled as one.
| Container | Jerry cans, 1 to 20 litre |
|---|---|
| Container | Lubricant bottles |
| Container | Grease buckets and pails |
| Container | Caps and closures for oils |
Packaging manufacturers in this sector
- Micro Tools
- Parekh Plast (I) Ltd.
- Mahaveer Plast
- Vardhaman Plasto Chem
- Bharat Propack Pvt. Ltd.
- Nexxon
- Paras Lubricant
- Creative Propack Inc.
- Nandan Petrochem
- Shree Sai Plast
- Shree Naina
- Raga Plastics
- Bloom Seal
- Dwarkadesh
- BPPL
1 Litre Lubricant Bottle Mould
Two-cavity blow mould for a one litre lubricant bottle, shown with its cavity and backing halves.
- Cavities
- 2
- Capacity
- 1 litre
- Material
- Tooling steel
2-Cavity Closure Mould
Two-cavity injection mould for a threaded closure, shown with the moulded caps.
- Cavities
- 2
- Runner
- Hot runner or cold runner
4-Cavity Carry Handle Mould
Four-cavity injection mould for a moulded carry handle, with the components still on the runner.
- Cavities
- 4
- Runner
- Balanced, hot or cold
Sector
Pharmaceutical Packaging
Bottles where every cavity has to produce the same bottle, and the finish has to stay the same across the whole set.
Multi-cavity pharmaceutical tooling is a consistency problem before it is a machining problem. The cavities are cut and polished as a set and checked against each other rather than individually, because a buyer filling from six cavities cannot have one of them running different.
| Container | Pharmaceutical bottles |
|---|---|
| Container | Multi-cavity bottle sets |
| Container | Closures and caps |
Packaging manufacturers in this sector
- SSF Plastics (I) Pvt. Ltd.
- Hitech
- Emami
- Sarthi Propack
- Plast Work
- GBC
- Devti Plast Industries LLP
- Scorpion Container Pvt. Ltd.
- Purvac Packaging Pvt. Ltd.
- Shree Balaji Food and Beverages
- Cool Caps Industries Ltd.
- Joy Cosmetic
The company presentation groups these customers under "Pharmaceutical & Consumer Products" and does not split them further, so the same list appears on both pages.
6-Cavity Pharmaceutical Bottle Mould
Six-cavity bottle mould, photographed on the machine with the cavities polished.
- Cavities
- 6
- Geometry
- Matched across all cavities
Sector
FMCG Packaging
Consumer bottles, jars and the closures that go on them, where the pack has to look right on a shelf as well as run on a line.
FMCG tooling carries the cosmetic burden: a grip panel, a label area that stays flat, a shoulder that does not wander. The geometry is often the difficult part rather than the engineering.
| Container | Consumer bottles |
|---|---|
| Container | Jars and wide-mouth containers |
| Container | Caps, closures and measures |
Packaging manufacturers in this sector
- SSF Plastics (I) Pvt. Ltd.
- Hitech
- Emami
- Sarthi Propack
- Plast Work
- GBC
- Devti Plast Industries LLP
- Scorpion Container Pvt. Ltd.
- Purvac Packaging Pvt. Ltd.
- Shree Balaji Food and Beverages
- Cool Caps Industries Ltd.
- Joy Cosmetic
The company presentation groups these customers under "Pharmaceutical & Consumer Products" and does not split them further, so the same list appears on both pages.
750 ml Bottle Mould
Single-cavity blow mould for a 750 ml bottle, cut in Alumec.
- Cavities
- 1
- Capacity
- 750 ml
- Material
- Alumec
2-Cavity Closure Mould
Two-cavity injection mould for a threaded closure, shown with the moulded caps.
- Cavities
- 2
- Runner
- Hot runner or cold runner
4-Cavity Carry Handle Mould
Four-cavity injection mould for a moulded carry handle, with the components still on the runner.
- Cavities
- 4
- Runner
- Balanced, hot or cold
Sector
Dairy Packaging
Bottles for dairy products, where the neck finish and a clean, even wall matter as much as the shape.
Named in the company presentation as one of the sectors we supply. No dairy tooling has been photographed for the site yet — the capability is there, the pictures are not.
| Container | Milk and dairy bottles |
|---|---|
| Container | Closures for dairy |
Sector
Industrial Packaging
Containers built to be handled, stacked and moved full — chemicals, agrochemicals and industrial fluids.
Industrial packs are judged on what survives a warehouse. Stacking load, handle strength and a pinch-off that holds after the container has been dropped are the things worth getting right, and they are all decided in the tool.
| Container | Jerry cans and carboys |
|---|---|
| Container | Chemical and agrochemical containers |
| Container | Industrial fluid packs |
5 Litre Jerry Can Mould
Two-cavity blow mould for a five litre stackable jerry can, with Beryllium Copper at the neck and the base pinch-off.
- Cavities
- 2
- Capacity
- 5 litre
- Material
- Tooling steel
Mould quotation desk
Have a mould requirement?
Send the drawing, the specification or a photograph of the container. We will review it and come back with a quotation and a dated schedule.